• Sourcing Solutions
  • Services & Membership
  • Help & Community

Quick Details

  • Place of Origin: China (Mainland)
  • Brand Name: V-REFLEX
  • Model Number: TF-HW254002
  • Technology: Micro Glass Bead
  • Retro-reflectivity: EN 471 Level2 ,ANSI 107-2010 Level 2
  • Color: Metal Silver
  • Standard Size: 2''x100m
  • Operation: Heat-activated adhesive
  • Application: Iron on Garments
  • Monthly output: 20,000 rolls
  • Dry clean: 2 cycle,ISO3175
  • Industrial wash: N/A
  • Home wash: 25 cycles at 60℃/140°F,ISO6330

Packaging & Delivery

Packaging Details Calculated at check out
Delivery Time 4-5 weeks after roder confirmation

Specifications

Home Wash Transfer Reflect Light Tape
Reflect at all angles
Meet ANSI/ISEA 107-2010 Level 2
Meet EN ISO20471

V-REFLEX

Reflective Material – Metal Silver Reflective Transfer Film TF-HW254002

Product Features

! Transfer in low temperature 130 °C (270 °F)

! EN ISO 20471 approved

! ANSI-ISAE 107 level 2

! Workable on wide range of substrate fabrics, polyester, cotton, lycra, etc.

! 25 home washing cycles at 40 °C per ISO 6330 (Properly transfer to backing fabric)

! 2 dry cleaning cycles per ISO 3175 Method 8.1

! Daytime color: Grey

! Max. Width: 1200 mm

! Retro Reflective Technology: Micro glass bead, Non-oriental sensitive.

 

 


Retro Reflectivity

V-REFLEX Reflective Material - Metal Silver Reflective Transfer Film TF-HW254002 exceeds the minimum reflectivity requirements of EN ISO 20471, ANSI-ISAE 107 Level 2, when tested at e = 0° or e = 90° in accordance with the procedures stated on standards. Minimum coefficients of retro-reflection required by standards are shown as below table.

Coefficient of Retro-reflection * (R’ or RA) cd/lux/m2

Observation Angle

Entrance Angle (β1, β2=0)

20°

30°

40°

0,20°(12’)

330

290

180

65

0,33°(20’)

250

200

170

60

1,00°(1°)

25

15

12

10

1,50°(1°30’)

10

7

5

4

 

Measured on new product at +5.0° entrance and 0.2° observation angles, V-REFLEX Reflective Material - Metal Silver Reflective Transfer Film TF-HW254002 typical has retro reflective performance as below table.

Product Code

Daytime color

Initial Average  RA

Minimum RA

TF-HW254002

Metal Silver

400

330


Physical Performance

V-REFLEX Reflective Material - Metal Silver Reflective Transfer Film TF-HW254002 will meet or exceed the following physical performance as noted. All RA values are at +5° entrance angle and 0.2° observation angle. 

Physical Performance

Test Method

Retro Reflectivity : (Initial)

EN ISO 20471

ANSI/ISEA   107-2010 Level 2

Abrasion : RA ≥ 100

5000  Cycles (EN 530 Method 2)

Flexing : RA ≥ 100

7500  Cycles (ISO 7854 Method A) 

Cold Fold: RA ≥ 100

-20 °C (-4 °F)( ISO 4675)

Temperature Cycle : RA ≥ 100

12 hours @ 50 °C (122 °F);

20 hours @ -30 °C (-22 °F)

Home Wash : RA ≥ 100

50 cycles @ 60 °C (140 °F)( ISO 6330)

Dry-Cleaning : RA ≥ 100

2 cycles per ISO 3175-2

 

Cutting and Plotting -

Die-cutting is recommended, although it can also be hand-cut or guillotined. When apply

V-REFLEX Reflective Material – Transfer Film to plotter for images cutting, remove adhesive side liner (if that product has one), the protective PET film on the surface of reflective side should be used as the carrier until plotted images are applying (laminating) to target substrate.

REMARK: Choose the recommended V-REFLEX Reflective Material - Transfer Film for plotter cutting. TF-HW254002 is NOT recommended for plotter cutting.

Printing -

Images may be printed on the surface of some V-REFLEX Reflective Material – Transfer Film. All inks should be continuously tested to ensure acceptable adhesion in the event of change occurring in the manufacturing process or composition of the ink. Prior to printing, wiping the surface with a soft cloth lightly dampened with isopropyl alcohol may help ink adhesion. Printed are as will not be retro reflective.

Heat Lamination

Product Code

Adhesive Side Liner

Reflective Side Liner

Lamination Temperature

Dwell Time

(seconds)

Line Pressure

TF-HW254002

None

PET Film

130-150 °C

(270-300 °F)

10-20

Firm

(30-40 psi)

 

1- Work on a flat surface where uniform heat and pressure can be applied. Avoid applying film over seams and stitches.

2- Remove adhesive side line (if that product has one), exposing dry adhesive. Do not remove reflective side liner.

3- Place V-REFLEXReflective Material - Transfer Film on substrate with the adhesive side down and apply heat and pressure as described in the table below. Place a non-stick slip sheet between the platen and laminating surface to prevent any excess adhesive transfer contamination.

4- Allow application to cool to room temperature before removing the liner covering the reflective side (if that product has one). Place application on a flat surface and remove the liner by lifting one corner and pulling (about 45o angle) in a continuous, smooth manner.


Washing Conditions

A colored clothing wash program without pre-wash should be used.

Recommendation:

• Wash temperature range: 0°C to 30°C  

• Max. Wash time at highest wash temperature: 12 minutes

• Max. Program time: 50 minutes

• Detergent: Brand powdered household detergents should be used. Recommended are detergents for delicate or coloured laundry. Refer to the detergent manufacturer’s recommendations for dosage in areas of high water hardness and for various degrees of garment soiling.

Wash temperatures higher than 40°C and industrial laundering processes are not recommended. The use of bleach or detergents containing organic solvent will result in a reduction in retro reflective performance.

Use of temperatures lower than 30°C will increase the lifetime of the reflective fabric. Actual lifetime will be dependent upon the detergent system and its dosage level.

 Do not use additional bleach

• No chlorine bleach.

• No bleaches on oxygen basis (e.g. sodium perborate).

Do not pre-soak laundry even in a low concentration of bleach.

Drying Conditions

• Tumble Dry: Tumble drying should be performed in a commercially available household dryer using the medium dry setting.

• Exhaust temperature should not exceed 70°C.

• Do not over-dry. Damp dry only.

• Air Drying: Line drying is recommended where possible.

Ironing Conditions

• Use medium setting, use press cloth.

• Do not apply steam.


Transaction History of the Supplier

Below is the information about the supplier's transactions conducted via Alibaba.com. If you require further details regarding the transaction data, please contact the supplier directly.

Transaction Overview

Transactions

Transaction Details

This supplier has completedtransactions with buyers from .

Shipping Destination
Transaction Value
Transaction Date
Email to this supplier
China (Mainland) | Trading Company
Supplier Assessments:
The supplier supports Trade Assurance – A free service that protects your orders from payment to delivery.
Supplier's Trade Assurance Limit: US $45,000
Learn More